fiat punto code p0340

Answers and questions: fiat punto code p0340

FIAT PUNTO HGT Diagnostic Code Faults - Help

Ok ive taken the plunge and read the diagnostic fault codes on my HGT and was wondering if someone could help to explain whats wrong (this is in relation to my car not starting as from this thread httpwww.fiatforum.compunto21408...ly-garage.html ) The codes that are displayed are 1 - NA - what does na mean in this context 2 - P0302 - cylinder 2 misfire detected 3 - P0325 - knock sensor 1 circuit malfunction

FIAT PUNTO occasional misfire - P0300 & P0340

02 reg Mk 2 punto 1.2 8 valve 85000 miles starts & runs perfect except what feels like a brief misfire now and again. The engine misfires for maybe 30 seconds and the yellow engine light comes on. Sometimes the engine light flashes and then goes out again when the misfire stops sometimes it stays on (not flashing) for a day or two. This happened about once a week for the last month or so. The codes

Zero the ECU codes then check with the engine cold and again when hot. If the sensor is failing its likely to be worse with the engine hot. Also check the cable connector contacts are clean.

FIAT PUNTO Punto Fault Codes

Hi I wondering if anyone could help I have plug a fault finder into my punto 1.2 8v petrol and its come back with these fault codes U1600 P0105 P0115 P0120and p0340 Any advise would be much help Thanks

FIAT PUNTO Need help with Punto Active Sport 16v

Hi everyone Im sorry I dont post a lot on this website but I do occasionally browse it. But that time has come where I am asking for help from you more experienced and knowledgeable lot here at the fiat forum. Seen as though I am very un-familiar with fiats I will try and explain as much as I can (even though I can rebuild MGRover engines from the back of my hand). So.. My girlfriends punto has begun

FIAT PUNTO fiat punto 1.2 16v cold starting problems

when you start the car first thing it takes about 5 times giving it a bit of throttle when you turn it over it turns for about 10 seconds then stops like you are advancing the timing its had new plugs ht leads lambda sensor read the codes and they are as follows p0340 camshaft position sensor a bank 1 circuit malfunction u1602 definition not none any ideas cheers Paul

Originally Posted by fisher72 when you start the car first thing it takes about 5 times giving it a bit of throttle when you turn it over it turns for about 10 seconds then stops like you are advancing the timing its had new plugs ht leads lambda sensor read the codes and they are as follows p0340 camshaft position sensor a bank 1 circuit malfunction u1602 definition not none any ideas cheers Paul p0340 - Might be worth while reading This old Thread on puntos about u1602 might help as well Ziggy

FIAT PUNTO Need opinions (

Hi everyone So basically I have a 53 plate fiat punto Active Sport 1.2 16v. It all started when I tried an induction kit on it it was fine for the journey to try it out then I parked back on the drive and left it for the night. The next morning the car was totally different (not saying that the induction kit had any part in this it just might do though) The car was misfiring and the power was gone

it keeps cropping up The camshaft sensor p0340 makes its Cam Shaft A circuit So it could be anything from the sensor to wiring to the ECU Get checking the wiring for high resistance corroded connectors wet connectors snapped cables freyd cables etc etc Check the sensor is the correct type and its producing the correct voltages (osilioscope is needed here) the 2 lambda sensors are generic or not fiat

FIAT PUNTO GRANDE PUNTO III 199 Grande Punto 1.4 16v Phase Sensor

Hi guys wondering if anyone can help. Ive got a 2006 Grande punto 1.4 16v in orange best colour ha anyway it has got a fault in the injection computer saying phase sensor fault code p0340 iv changed the sensor and the same fault occured so i checked the wiring from the feed which had just under 5 V and checked the signal wire whcih was ok and checked the earth which again was fine so then i think it

FIAT PUNTO GRANDE PUNTO Eobd light (

Hi all my eobd light has come on and after warming the car up I noticed the temp gauge drop suddenly Ive looked but cant find no help is the car safe to drive as Ive got a long drive to work to do tonight. Any help will be much appreciated so thanks in advance P.s I aint a mechanic so please talk basic talk to me

sadly there is no way on earth anyone can guess whats going on .... the OBD2 code outputs (dependent on the car) can be a wee bit long...... Until you have the code read no one can second guess as it could be one of these P0001 Fuel Volume Regulator Control CircuitOpen P0002 Fuel Volume Regulator Control Circuit RangePerformance P0003 Fuel Volume Regulator Control Circuit Low P0004 Fuel Volume Regulator

FIAT PUNTO GRANDE PUNTO 1.3 75hp Multijet check engine

Dear All Nowadays I experience strange issue with the 75hp 1.3 Multijet. As the engine starts sometimes just after the start the check engine light comes up. 2 weeks ago a friend of mine read the code with the fiatecuscan and found p0340 Camshaft position sensor circuit....... Strange that the error is possible to be erased and totally randomly it could come up but only right after the start of the

FIAT PUNTO Engine issues

I blew the HG on my MK2 8v punto just over a month ago had that and many other gaskets replaced and since then i am having many issues with the engine. The engine light on the dashboard keeps popping on sometimes accompanied by the oil light. On one occasion the engine idle speed was 3000revs and another occasion the engine only ticked over if i pushed the throttle pedal down. The engine error codes

FIAT PUNTO speedgear problems

hi everyone here goes. I have just got hold of a 1.2 16v mk2 punto speedgear it had engine mangement lights on so i scanned them and they were lambda sensor 2 failure and camshaft sensor failure and a little light pops up on dash next to the handbrake light. it looks like the handbrake symbol but insted of lines down the side its dashes. so i replaced the lambda and camshaft with new parts and started

just got a brand new bosch sensor imported and its still throwing up code p0340 definition means camshaft sensor circuit malfunction any ideas could it mean the sensor is ok but wires on car are faulty

Originally Posted by fiat brava jtd elx 105 just got a brand new bosch sensor imported and its still throwing up code p0340 definition means camshaft sensor circuit malfunction any ideas could it mean the sensor is ok but wires on car are faulty Hi mate yes could well be you need to check your getting voltage at the sensor. Alan

FIAT PUNTO ecu problem

Hey I posted before about this problem but it seems to have changed a bit First thing- loss of power and engine management light Second came a misfire Changed front lamba no look changed plugs and wires and misfire went but still no power and engine management light Error codes are p0340 U1602 and U1702 one of these is to do with cam sensor so changed that no difference cleaned map sensor no difference

You can Google for these codes. In the case of p0340 Camshaft Position Sensor Circuit Malfunction. So it could be any part of the wiring to the CPS. And so on. Another approach which is useful is to clear all the codes and drive the car until the ECU light comes on then re-read. This often gives just one code (or one fault) which will have triggered all the others.

FIAT PUNTO GRANDE PUNTO III 199 Help fiat punto grande 14 twin cam

Just bought punto wont rev over 5000 rpm any ideas my code reader says only fault crank shaft postion sensor replaced still says same

code p0340

FIAT PUNTO fiat punto 1.2 16v cold starting problems

when you start the car first thing it takes about 5 times giving it a bit of throttle when you turn it over it turns for about 10 seconds then stops like you are advancing the timing its had new plugs ht leads lambda sensor read the codes and they are as follows p0340 camshaft position sensor a bank 1 circuit malfunction u1602 definition not none any ideas cheers Paul

FIAT PUNTO GRANDE PUNTO 57 plate t-jet problem - engine management light

Right guys the other week the engine management light came on (constant) saying check engine. (so topup with oil and check coolant and everythings fine again.) Came on there tonight again (constant) saying same message. Now ive looked at the other old threads posted up but nothing up to date in basically a year. So is it the egr valve or is it something else And please dont tell me to buy a reader of ebay like in other threads either you have an answer or you dont.

Buy a reader of ebay...... Is the best answer your going to get that light can come on for one of the following reasons.. P0100Mass or Volume Air Flow Circuit Malfunction P0101Mass or Volume Air Flow Circuit RangePerformance Problem P0102Mass or Volume Air Flow Circuit Low Input P0103Mass or Volume Air Flow Circuit High Input P0104Mass or Volume Air Flow Circuit Intermittent P0105 Manifold Absolute

FIAT PUNTO GRANDE PUNTO 1.9 mjet in limp mode with phase sensor fault

hi was driving absoluty fine then suddenly went into limp mode turned off restart and would rev at around 1500rpm on its own at idle then went to bring into workshop and vehicle wont start now fault codes are p0340 phase sensor and P0641 power supply any one had this problem have got continuity in sensor and only recieving 5v at plug any one no what power should be sent to the sensor

FIAT PUNTO camshaft position sensor

Hi Ive got a punto 1.2 16v sporting.Just changed the head gasket and am now getting missfires and read the code and its saying camshaft position sensor.Can anyone tell me where this is Is it possible I disconnected it while changing the head gasket

The code that im getting is p0340 - camshaft position sensor A circuit. Is the cam sensor the one that is near the crank sensor If so i disconnected this and started the engine and it ran the same.Im thinking maybe Ive got the cam set up wrong from when I rotated it. This is what i did I rotated the crank and noted that pistons 2 and 3 were going up. I then rotated the cam so that the slots on both

FIAT PUNTO Start of the headgasket today )

Start of the headgasket for my 16v sporting Got the timing tools coming on thursday but starting to take everything off now Shall i still mark everything up or is it safe to just pull everything off and time it up at the end of the headgasket Also im lapping the valves when i get the head off can i manually pull the valves out or do i HAVE to have the valve extractor

Just finished the headgasket without too much cursing haha Timed it perfect Done everything by the haynes manual started it and it was ok but seems a bit hesitant... plugged in the diagnostics and its come up with 7 codes P0202 injector circuit Cylinder 2 P0135 02 sensor p0340 camshaft position sensor A P1135 (undefined) P0130 o2 sensor U1702 (undefined) P1314 (undefined) .... help

Ask an expert